Underground manifold Underground manifolds are pre-fabricated and designed specifically for use with Kensa ground source heat pump installations. They provide security and a central position to connect together the heat pump’s underground pipes. Underground manifold features Underground manifolds are manufactured from tough water-resistant polyethylene. They are available in a range of sizes with differing numbers…
More DetailsKensa offers advice and guidance on the care that has to be taken with heat pump systems using thermal stores to ensure efficiency is maintained. Key considerations for thermal stores Thermal stores A thermal store will use a volume of stored hot water to produce domestic hot water via an indirect coil or tank-in-tank system….
More DetailsKensa can supply three lengths of straight pipe for use with all Kensa ground source heat pumps if pre-coiled slinkies aren’t appropriate. Find out more about these ground arrays on our slinkies and straight pipe page. Straight pipe features Dimensions: Supplied in 200m, 250m and 300m lengths. Straight pipes are manufactured using 32mm black High…
More DetailsShowcase Kensa’s most advanced – and the world’s most intelligent – ground source heat pump with this affordable Kensa Evo Heat Pump case. This hollow Evo heat pump case demonstrates the quality of workmanship, elegant aesthetics, and enhanced ease of installation features of the Kensa Evo. The Evo case features a blank Genesis System Manager…
More DetailsKensa provides advice on using secondary hot water returns with heat pump systems to ensure hot water is immediately available for properties. What are secondary returns? These are used to avoid excessive water draw off before the hot water at the tap is at the correct temperature. Heat pumps & secondary returns Any pumped return…
More DetailsAn important factor of any ground source heat pump installation is ensuring that the ground arrays are purged of air and filled with antifreeze. Kensa’s ground arrays purging demonstration kit provides hands-on training to ensure any installer is competent in this important stage of a ground source heat pump installation. Ideal for installer training Demonstrates…
More DetailsKensa recommends the Clarke SPE1200SS (part no. 051012200) to purge ground arrays, in order to remove air in the pipes to avoid the heat pump system freezing. The pump comes ready to take a 1” BSP fitting. As a kit, Kensa Heat Pumps provides 2 x 1” BSP Male Iron to 28mm Speedfit connectors. This…
More DetailsPre-coiled slinkies Kensa Heat Pumps manufactures pre-coiled slinkies on-site for supply with all Kensa ground source heat pumps, enabling ease of installation. Slinky pipe features Three pre-coiled slinky pipe length options: 30m, 40m and 50m (indicated by a coloured cable tie). Each slinky features a straight header pipe (typically 25m long), a pre-coiled section (30m,…
More DetailsWater source heat pump pond mats Kensa Heat Pumps manufacture and supply ready-made pond mats for ease of installation with all Kensa ground source heat pumps where a water source is available. Kensa pond mats are specifically designed to ease installation while maximising the energy absorbed from the water. The pond mats can be weighted…
More DetailsWant to teach students, trainee installers or delegates all about ground source? This self-contained, fully functioning demonstration unit features the real-life components of a ground source heat pump in one easily transportable and self-explanatory unit. How does this heat pump demonstration unit work? Kensa’s heat pump demonstration unit is just like a real ground source…
More DetailsKensa has partnered with leading cylinder manufacturers to design and produce mains pressure hot water cylinders especially for ground source heat pumps. These cylinders work with all Kensa ground source heat pumps to deliver affordable and eco-friendly hot water, whenever it is needed. Kensa’s hot water cylinders are available in a range of sizes, in…
More DetailsDemonstrate the best in British-made low-carbon technology with specialist ground source heat pump training units. We offer two versions of a complete system, showcasing our most popular product ranges; the Kensa Evo (ideal for medium to large properties) and the Kensa Shoebox (ideal for smaller homes and multiple property projects). With a complete and fully…
More DetailsKensa has partnered with leading cylinder manufacturers to design and produce buffer tanks for specific use with Kensa ground source heat pumps. Buffer tank models available include: 100 litre Advance Appliances two connection compact mild steel square tank 100 litre McDonald buffer vessel SB100 150 litre McDonald buffer vessel SB150 200 litre McDonald buffer vessel…
More DetailsKensa’s ground heat pumps are designed to be used with a non-toxic antifreeze. Thermox DTX has been specially formulated for use in ground source heat pump systems, delivering a non-flammable and non-toxic solution which utilises the advantages ethylene glycol as opposed to propylene glycol. Benefits of Thermox DTX heat pump antifreeze Non-toxic. Thermox DTX has…
More DetailsAbove-ground manifolds Kensa Heat Pumps manufactures above ground manifolds for use with all Kensa ground source heat pumps. Our manifolds are available in a range of sizes, and feature quality water resistant components. To provide ease of installation and adaptability, models are available in universal, left and right handing. Models available: 1 Way Manifold, 32mm…
More Details