In this article the Technical Support Team at Kensa Heat Pumps give their top tips for proactive maintenance on ground source heat pump systems to ensure you stay warm and cosy throughout winter.
One of the unique benefits of ground source heat pumps is their minimal maintenance requirements and long life expectancy. However, as with all heating systems, it is good practice for the heating distribution system, including energy collectors, to be proactively checked and maintained to ensure optimum performance when colder weather is on the horizon.
Temperatures below ground remain relatively constant all year round, so a sudden drop in air temperature during winter will not affect the performance of a ground source heat pump, nor does the impact of exposure to the elements affect operation, as it would an air source heat pump.
End users with renewable heating technology, such as ground source heat pumps, have another reason to get their systems checked regularly. Most end-users are interested in claiming subsidies via the Government’s Renewable Heat Incentive (RHI) scheme, and as such have ongoing obligations once they have successfully applied. OFGEM states:
To make sure your renewable technology is in good working order, we recommend that you maintain your renewable technology in line with manufacturer’s instructions to ensure it works at an appropriate level of efficiency…If your renewable technology stops generating heat and needs repair, your payments may be stopped or suspended.” – (Essential Guide for Applicants Version 3 March 2016)
Heating Distribution System
Mike Elliott, Kensa Technical Support, says:
Well designed ground source heat pumps have a design life of 20+ years and require only a minimal amount of maintenance. However it is important that the whole system is checked, ideally before the heating season starts in earnest.
Mike recommends the following basic checks are made on the heating distribution system:
• Check the inhibitor levels and ensure no corrosion or degredation has occurred.
• Make sure that all pump valves and actuators on the system are functioning correctly.
• Ensure all room stats and programmers are operating correctly and are programmed correctly.
• If any components require a battery to function, check that the battery has charge.
• If the system has filters or a MagnaClean, check that this is cleaned and/or serviced.
• Check the pressure of the system; Kensa recommends that it is above 2 bar.
• Peform a gas charge pressure check on the expansion vessel.
Renewable Energy Collectors
Tom Worth, Kensa Technical Support, says:
This is where the maintenance of a ground source heat pump system becomes slightly different to that of a standard fossil fuel system, as it is important to ensure that no issues can occur in the collectors that harness the renewable energy from a ground or water source.
Any issues with the energy collection system could mean the heat pump has to work harder and hence becomes less efficient. In the worst case the source energy could become depleted causing the heat pump to stop operating altogether.
Tom recommends the following quick and easy checks on ground source heat pump energy collectors:
Slinky pipe and sealed boreholes
• Samples of thermal transfer fluid should be taken and the concentration of the antifreeze solution measured using a refractometer.
After a number of years the concentration of antifreeze solution within the ground arrays can drop due to possible top-ups of fresh water to maintain the ground array pressure. Antifreeze solution provided by Kensa contains an anti-bacterial agent and an inhibitor to avoid bacterial growth and corrosion. Maintaining the correct concentration of this antifreeze solution is important as it will stop the system from freezing and also prolong the lifespan of the circulation pump. The bacterial agent will ensure no bacterial growth occurs, thus further increasing the lifespan of the antifreeze.
• The manifold should be thoroughly inspected, checking that any insulation is still in good condition and the components are still fit for purpose. Ground array manifolds on the ground collector can suffer from condensation due to the low temperatures of the thermal transfer fluid, which if not properly controlled can cause damage.
• After a period of time any disturbed ground will settle, so manifolds should be checked for strain on pipework connections caused by ground settlement. It can take up to 12 months for any disturbed ground to fully settle and if any pipework is under strain this must be remedied.
• The pressure of the thermal transfer fluid within the ground array should be checked and increased if required. Kensa recommends that it is above 2 bar.
• It is advised that pond mats are inspected, cleaned and maintained regularly. After a period of time sediment, mud and leaves could build up around and under the pond mat collectors causing a potential loss of performance and reduced ability to harvest heat from the water.
• Check the manufacturer’s guidelines on maintenance for external heat exchangers. Manufacturers of plate heat exchangers can recommend that the plate gaskets are replaced every two years.
• Any external filters or treatment systems fitted to an open loop system should also be checked and maintained in line with the manufacturer’s guidelines.
• Open loop heat exchangers can suffer from condensation damage due to running with liquid at lower than ambient temperatures, which if not properly controlled can cause damage. Any heat exchanger should be inspected checking that any lagging is still in good condition and any components are still fit for purpose. If corrosion has started, these areas can be treated to preserve their longevity.
• The open loop pump and pump control may also need to be maintained and it is advisable to check with the manufacturer or suppliers for their recommendations.
• Particularly for any surface water sources, check inlets and outlets are free from vegetation and also from any flotsam and jetsam.
An evolution in heat pump maintenance
Todd Whymark, Kensa Technical Support, says:
Kensa’s new Evo Series makes life easier by automatically performing some of the standard system maintenance checks listed above. To do this, Kensa developed our own control board which is the brain of the new Evo heat pump. The custom built software provides live status updates and innovative diagnostics which permits the control board to pre-empt system irregularities using warning safety levels.”
Other new features include a water pump exercise program that is activated when the heat pump is dormant for a prolonged period, eliminating the need for user interaction to ensure that the water pump still spins and is operational. The Evo’s new pipework arrangement has alleviated the need for bleeding the heat pump before the heating season, as the heat pump has no internal high points for air pockets to collect.
The Evo will also warn of a lack of flow which can indicate to the homeowner that the system is losing flow possibly due to blocked filters. A warning can be set on the unit allowing planned maintenance to occur before the unit goes to alarm and shuts down to protect itself or any significant damage occurs.
A technical information sheet on the Evo series is available here:
Contact Kensa’s Technical Support Team
Kensa Heat Pumps has a dedicated Technical Support team that can help, advise and direct any pre-heating season enquiries about Kensa Heat Pump systems. They can be contacted on 0845 680 4328.