Technical Data

Twin Compact Series Technical Specifications

Model Range	Standard	Standard	Standard	High Temperature	High Temperature	Hybrid	Hybrid	Three Phase	Three Phase	Three Phase
Phase	Single	Single	Single	Single	Single	Single	Single	Three	Three	Three
Nominal thermal kW rating at B0/W35	16	20	24	12	17	15	21	20	24	30
Nominal thermal kW rating at B0/W60				11.3	15.3
Nominal thermal kW rating at B0/W65				11	15
Part Number	C160-T1H	C200-T1H	C240-T1H	H124-T1H	H170-T1H	M150-T1H	M210-T1H	C200-T3H	C240-T3H	C300-T3H
MCS Approved	BBA0055/07	BBA0055/08	BBA0055/09	BBA0055/28	BBA0055/29	BBA0055/32	BBA0055/33	BBA0055/13	BBA0055/14	BBA0055/15
Performance data - rated heating output at B0/W35 BS EN14511
Power consumption	5.2	5.8	7.2	5.79	7.23	3.9	5.3	5.7	6.9	8.1
Co-efficient of Performance at B0/W35	4.15	4.16	4.14	4.16	4.15	4.15	4.14	4.15	4.18	4.15
Co-efficient of Performance at B0/W65				2.08	2.1			2.31	2.39	2.3
Immersion heater output	Kensa heat pumps do not feature back-up electric immersion heaters
Brine (primary): Based on 0?C in / -4?C
Design flow rate kg/min	52.7	61.2	75.4	39	43.9	47.16	70.14	61.5	76.2	91.6
Pressure drop kPa at design flow rate	11.2	15.3	22.2	6.79	12.6	12.8	22.7	15.4	22.6	31.5
Max inlet temperature ?C	15	15	15	20	20	15	15	15	15	15
Min temperature ?C (outlet)	-5 (at standard settings)	-5 (at standard settings)	-5 (at standard settings)	-5 (at standard settings)	-5 (at standard settings)	-5 (at standard settings)	-5 (at standard settings)	-5 (at standard settings)	-5 (at standard settings)	-5 (at standard settings)
Heating water (secondary): Based on 30?C in / 35?C out
Design flow rate l/min	50.6	58.4	72	40.2	48.8	44.03	61.86	58.2	71.8	85.9
Pressure drop kPa at design flow rate	9.3	12.3	18.7	5.94	8.71	7.1	13.9	12.3	18.6	26.5
Max flow temperature ?C***	55	55	55	65	65	65	65	55	55	55
Electrical values at B0/W35
Rated voltage	220 - 240V / 50Hz	220 - 240V / 50Hz	220 - 240V / 50Hz	220 - 240V / 50Hz	220 - 240V / 50Hz	220 - 240V / 50Hz	220 - 240V / 50Hz	400 V / 50 - 60 Hz	400 V / 50 - 60 Hz	400 V / 50 - 60 Hz
Power supply rating amps	63	63	63	50	50	50	60	25	32	32
Rated current (max) amps	43.7	52.5	65.4	42.9	48	43	58	18.9	23.6	27
Typical running current at B0/W35 amps	27.4	28	35.4	26.9	27.9	25	29	12.2	15.2	17.5
Starting current amps ****	44	44	48	42	42	44	48	55	68	79
Refrigerant circuit
Process medium	R407C	R407C	R407C	R134a	R134a	R407c/R134a	R407c/R134a	R407C	R407C	R407C
Fill volume kg	2.2	2.4	2.6	2	2.6	1.0 / 1.4	1.3 / 1.4	2.4	2.6	2.4
Compressor type	Scroll	Scroll	Scroll	Scroll	Scroll	Scroll	Scroll	Scroll	Scroll	Scroll
Dimensions
H X W X L (mm)	900 x 900 x 570	900 x 900 x 570	900 x 900 x 570	900 x 900 x 570	900 x 900 x 570	900 x 900 x 570	900 x 900 x 570	900 x 900 x 570	900 x 900 x 570	900 x 900 x 570
Dry weight kg	167	170	180	165	167	167	180	170	180	185
Operating pressure
Brine circuit min (primary) bar g	0.3	0.3	0.3	0.3	0.3	0.3	0.3	0.3	0.3	0.3
Heating water circuit min (secondary) bar g	0.3	0.3	0.3	0.3	0.3	0.3	0.3	0.3	0.3	0.3
Low pressure reset bar g	1.8	1.8	1.8	1.8	1.8	1.8	1.8	1.8	1.8	1.8
Connection sizes
Primary IN and OUT (speedfit) mm	50	50	50	28	50	50	50	50	50	50
Heating flow and return (speedfit) mm	28	28	28	28	50	28	28	28	28	28
Performance (based on Average Climate) @ 35?C
ErP rating	A++	A+	A+	A++	A++	A++	A+	A++	A+	A+
SCOP*****	3.99	3.82	3.87	3.98	4.03	4.14	3.93	4.15	3.83	3.69
Seasonal space heating energy efficiency	152%	145%	147%	151%	153%	158%	149%	158%	145%	140%
Performance (based on Average Climate) @ 55?C
ErP rating	A+	A+	A+	A+	A+	A+	A+	A+	A+	A+
SCOP*****	3.18	3.14	2.94	3.14	3.27	3.25	3.13	3.3	3.13	3.11
Seasonal space heating energy efficiency	119%	118%	110%	118%	123%	122%	117%	124%	117%	116%
Sound Power Level
Sound Power Level (dB)	58	59	61	64	60	66	63	59	59	59

* The COP figure quoted is calculated as per EN14511

** In-built immersion heaters will increase running costs and CO2 emissions as they use direct electricity, because of this Kensa heat pumps do not include them.

*** By increasing the flow temperature from the heat pump the efficiency of the unit will drop and the COP decreases.

**** Kensa single pumps heat pumps incorporate smart starts as standard to limit the starting current of the compressors. For full details on how the starting currents are calculated please contact Kensa.

Note: Design flow rates are for a ground temperature of 0°C and –4°C and a load temperature of 30°C and 35°C.